Arris is one of the best cable modem services that enables a gigabit-speed network. Most of the Arris routers ship with the default username as “admin“, the default password is “password“ and the default IP address as
These credentials are required when you want to login into your router’s web interface. Therefore, if you have to make changes in configurations, you need these details to access the router’s settings. This article explains what to do when you forget your Arris router password, require resetting the router to its default password, or when the password reset does not work.
Arris Default Usernames and Passwords
Even though most of the Arris products come with the default credentials, some of the models do not follow the same standards. You can check the default usernames and passwords for each model from the table below:
Model | Default Username | Default Password | Default IP Address |
DG3450 | admin | password | 192.168.0.1 |
DG860P2 | admin | password | 192.168.0.1 |
DG950A | admin | password | 192.168.0.1 |
SB8200 | admin | password | 192.168.100.1 |
SBG10 | admin | password | 192.168.0.1 |
SBG6700-AC | admin | password | 192.168.0.1 |
SBG6900-AC | admin | password | 192.168.0.1 |
SBG8300 | admin | password | – |
SBR-AC1750 | – | password | 192.168.0.1 |
SBR-AC1900P | admin | password | 192.168.0.1 |
SBR-AC3200P | admin | password | 192.168.0.1 |
TG1672G | admin | password | 192.168.100.1 |
TG1682G | admin | password | 10.0.0.1 |
VAP4641 | admin | – | 192.168.1.253 |
WR2100 | admin | password | – |
Forgot Your Arris Router Password?
It is likely that you changed your Arris password and username and forgot the new credentials. If you have already changed the default factory settings and replaced a new username and password, you have to enter the new credentials to access the router. However, if you forgot either the password or the username, it is completely fine as you can change it back to the default settings. All Arris routers ship with a pre-set username and password that you can revert to when a problem arises.
Reset Arris Router to Default Password
Reverting the router credentials back to their factory settings is simple and hassle-free. To return your router back to its original username and password, you have to follow the 30-30-30 reset. The steps to do the same are as follows:
- Switch on the Arris router. When the router is switched on, press and keep holding the reset button for 30 seconds.
- While you are holding the reset button pressed, disable the router’s power by unplugging it and continuing holding the reset button for another 30 seconds.
- While you are pressing the reset button, switch on the power to the unit once again. Then, hold the reset button for 30 seconds more.
Carry out the above-mentioned steps carefully. Once you complete this process, your Arris router goes back to its default factory settings. You will now be able to access the settings of your router by entering the default credentials of your router model. To verify the factory-set username and password of your device, check the table above. If the router reset did not work out, check out the Arris 30-30-30 factory reset guide. After accessing the router, make sure you change the default username and password to ensure security.
I Still Can’t Access My Arris Router With The Default Password
If you cannot access the router with its default password, ensure that you have followed the reset procedure correctly. Once the procedure is correct, the Arris router will surely revert to the default factory settings. Therefore, try the method again carefully, and if it still does not work, it is probably because your router is under damage.
Conclusion
Most of the Arris router models come with the default username and password. After changing the credentials, if you have any problems regarding accessing the router, you can reset it to its factory settings by following the instructions given in this article. I hope this has been helpful to you.